Connecting iAtty, Odysseus or Penelope on a GGTS

WARNING: If you are here because of a link you found in a site that sells e-cigs, you have to know that these sites sells fake GG series and you are sold down the river. If you really want to have the real deal then please check The Golden Greek forum here:

GG on ECF

Or ask a question to one of the Golden Greek authorized sellers:

GG Greece
GG USA
GG Italy

IMPORANT NOTE: A new GG original adapter has been made by Imeo for this purpose, and

it is the recommended and official method to connect tanks and fat atomizers to the GGTS.

Please take a look at the following video:

GGTS Adapter (English)

The GGTS Adapter (picture by COV).

Thanks to Ariel_MX

This guide shows 5 ways to connect a GG rebuildable atomizer with 510 base / connector or any other tank with 510 connector on a GGTS.

Adapters used in this guide:

From left to right:

901battery -> 808-D Atomizer
901-510
510-510 (shortie)
510-510
901-510
GGTS 510 -> 901 re-threader

Without Airflow Control

Method 1

Adapters used*:

Shortie 510 - 510

Normal 510 - 510

*Adapters installed on the GGTS connector.

Results:


Atomizer tank won't sit flush on top, airflow control will not work with this method.	Connector Pin significantly protuberant.

Method 2:

Adapters used*:

510 - 901 rethreader¹

901 - 510

Shortie 510 - 510

*Adapters installed on the GGTS connector.

¹ Included with GGTS.

Results:


Atomizer tank won't sit flush on top, airflow control will not work with this method.	Connector Pin less protuberant than method 1.

With Airflow Control

Method 3

Adapters used*:

510 - 901

901 - 510

*Adapters installed on the GGTS connector.

Results:


Atomizer tank will sit flush on top, airflow control will work fine.	Connector Pin significantly protuberant.

Method 4

Adapters used*:

510 - 901 rethreader¹

901 - 510

*Adapters installed on the GGTS connector.

¹Included with GGTS.

Results:

Use without the Collector Tank Draw Cap (brass part on pictures).

Atomizer tank will sit flush on top, airflow control will work fine.

Notice the Connector Pin resultant lenght.

This method keeps the GGTS total length to a minimum.

Method 5

Adapters used*:

510 - 901 rethreader¹

901 - 808

901 - 510

*Adapters installed on the GGTS connector.

¹Included with GGTS.

Results:

Atomizer tank will sit flush on top, airflow control will work fine.

If you wanna keep the GGTS original look (Collector Tank Draw Cap installed) this is the prefered method.

Notice the Connector Pin resultant lenght.

The 901 - 808 adapter.
901-808adapter.jpg

iAtty on ss GGTS with AW IMR 18350 battery, method 5.

Example (step by step method 5):

2 Adapters, GGTS rethreader and GGTS connector unassembled.

The 901 - 510 and 901 - 808 adapters.

From bottom to top:

GGTS rethreader

901 - 808

901 - 510

From left to right:

GGTS rethreader

901 - 808

901 - 510

Top view of the 901 - 808 adapter.

First screw the GGTS rethreader in the GGTS connector.


GGTS rethreader in the GGTS connector.	Then screw the 901 - 808 adapter on the GGTS rethreader.	GGTS rethreader and 901 - 808 adapter installed on GGTS connector.

Screw the 901 - 510 adapter on the 901 - 808 adapter:

From bottom to top:

GGTS connector.

GGTS rethreader.

901 - 808 adapter.

901 - 510 adapter.

Assemble the GGTS connector:

From bottom to top:

GGTS connector.

Collector cup.

Air flow control ring.

Install the GGTS 901 / 510 top lid (brass cap on the picture).

You may need to unscrew just a little the brass cap.

GGTS Connector pin view.

Notice the connector pin lenght.

The 901 - 808 (bottom) and 901 - 510 (top) adapters.

GGTS full connector assembled + iAtty.

(stainless steel top lid).


Close-up: GGTS full connector assembled (brass top lid) + iAtty.	GGTS connector assembled (stainless steel top lid) + Odysseus.	Close-up: GGTS full connector assembled (stainless steel top lid) + Odysseus.